In audio, the opposite of Unbalanced. For us balanced refers to a type of AC electrical signal having two "legs" independent of ground. One is generally considered positive (+) and the other negative (-) in voltage and current flow with respect to ground. Unlike unbalanced audio lines there is no "signal" carried in the shield or ground connection unless there is a fault. The main benefit is that any noise that gets induced into the line will be common to both the positive and negative sides and thus canceled when it arrives at its destination, assuming the destination is balanced. This phenomenon is called "Common Mode Rejection" and basically just means that any signals common to both the positive and negative legs of balanced lines get canceled. This happens because when the receiving device looks at the signal the common noise actually shows up as out of phase with itself, and gets cancelled. Think of it as if the negative (-) signal gets inverted to positive (+) before use, which puts the desired audio signal in phase with the already positive other leg and at the same time causes the undesired common noise to become out of phase with itself. Clear as mud? Balanced lines are generally much better for long cable runs due to their ability to reject induced noises. XLR and TRS type cables are designed to transmit balanced audio from one balanced device to another. A standard 1/4-inch guitar cable is an example of an unbalanced cable. Another (newer) application of balancing that is becoming popular in audio systems is the idea of balanced power systems. Fundamentally the concept is the same. There is a positive and negative (with respect to ground) leg of electricity at every electrical outlet. The idea is that the power supply of any devices connected can then reject any noise induced on the AC line and thus will produce cleaner audio. We'll talk more about balanced AC systems in the future.
Unbalanced
In electronics, a condition where the two legs of the circuit are unbalanced with respect to ground, usually because one leg is kept at ground potential. In other words: An audio signal requires two wires or conductors to function. In an unbalanced situation, one of those conductors is used to carry both signal and ground (shield). Unbalanced circuits tend to be less expensive to construct, but they are much more susceptible to induced noise problems than their balanced counterparts. This is because any induced noise in one conductor is not canceled by similar noise in the other conductor (as in a balanced line) and may be carried with signal into connected equipment. In general, unbalanced lines should be kept as short as possible (certainly under 25-30' maximum) to minimize potential noise problems.
1/8 (Mini)
1/8 inch diameter plug (or jack) used in smaller audio visual interconnects. The connector may be TRS or TS, as well as some other configurations. This is the size of most of the Walkman style headphone connectors.
AES
AES/EBU is the most common alternative to the S/PDIF standard and the most common AES/EBU physical interconnect is AES Type I Balanced - 3 conductor, 110 ohm twisted pair cabling with an XLR connector.
BNC
A type of coaxial connector often found on video and digital audio equipment, as well as on test devices like oscilliscopes. In audio gear, BNC connectors are normally used to carry synchronizing clock signals between devices. BNCs are bayonet-type connectors, rather than screw on, or straight plugs. They are named for their type (Bayonet), and their inventor, Neill Concelman.
DB25
A type of D-Sub connector. DB-25's are commonly found on computing equipment where they are employed to connect peripherals. They are common to parallel ports or RS-232 ports on PC computers, but also often used in a variety of ways in the audio community. For example, TASCAM commonly uses the DB-25 connector for analog and/or digital I/O on their products, as do some other brands.
Elco
A brand and type (like Crescent wrench) of multi pin connector used in audio systems and equipment for connecting multi pair cable with one connector (instead of many). Elco is made in the U.S. and Edac is made in Canada and both come in many different varieties. They both come in 20, 38, 56, 90, and 120 pin configurations. There are male and female connectors (plug and receptacle in Edac nomenclature). The male connector can be identified by its polarizing pins on the plug, whereas the female has polarizing sockets. Either sex can have the actuating screw or the fixed nut for attachment. All that is required is that there is one each. On the back of an ADAT, for example, the Elco is a female 56 pin, with fixed nut. The cable you plug in, therefore, is a 56 pin male with actuator screw.
Insert/Y Cable
A cable used to split a signal into two parts or combine two signals into one. The term Y Cable is used because the cable is like (and looks like) the letter Y, where there are two parts joined into one, or one split into two, depending upon how you look at it. Y Cables are common throughout audio as a simple and easy way to accomplish these two tasks. There are times, however, where they can be used in inappropriate ways, sometimes with disastrous results. For example, two MIDI signals cannot be combined using a Y cable. Two outputs from power amps cannot (under most normal circumstances) be combined via a Y cable (this will usually result in a substantial repair bill). Even in situations where Y cables can "work" the results are sometimes less than ideal. One must consider the output and input impedances, signal levels, and other factors of the devices in question before indescriminately combining or splitting their signals.
Opti cal
Optical cables are for compatible two-channel S/PDIF connections and ADAT lightpipe connections. The ADAT optical connections for transferring digital data 8-tracks at a time have become a standard of the industry and are used in a wide range of products from many manufacturers.
RCA
The phono plug was so associated with RCA in the beginning (see WFTD Phono Plug) that it actually became known as the RCA plug. Today the majority of people refer to it as an RCA connector, even though that isn't the technically correct name.
S/PDIF
A format for interfacing digital audio equipment together, S/PDIF (Sony/Philips Digital Interface Format) is considered a consumer format, and is largely based on the AES/EBU standard. In fact, in many cases the two are compatible. There are, however differences between the two formats, particularly in the channel status and user bits.
S/PDIF typically uses either unbalanced, high impedance coaxial cables or fiber optic cables for transmission. When using coaxial cables for transmission, it is normally best to keep cable lengths to a minimum, and to use the best quality 75 ohm video-type cables available.
TDIF
Generally pronounced TEE'-dif, it is an acronym for Tascam Digital InterFace. This is the protocol Tascam developed to use in their MDM and digital mixing products for doing digital transfers of audio. TDIF connections are made via a 25-pin d_Sub connector and data is carried on shielded cable. The TDIF standard is currently one of two major formats (the other being ADAT optical) widely used in pro and semi-pro MDM related products for digital transfer of more than two tracks of audio simultaneously using only one cable.
TRS
Abbreviation for Tip Ring Sleeve. This is the descriptively accurate term used to describe 1/4" (or 1/8") balanced connectors. A TRS plug can be found at the end of most headphone cords if you want to know what one looks like. They look like a standard 1/4" plug with an extra section in them. The three sections of the shaft are called the Tip, Ring, and Sleeve (a "standard" 1/4" connector just has a tip and sleeve). TRS connectors are used wherever it is desired to have two conductors plus a ground (shield) in one plug. Common uses are as a way to connect balanced equipment (where the TRS plug has a positive, negative, and ground connection), or stereo unbalanced equipment (left and right are on the Tip and Ring, with a common ground) like headphones, or as an insert for your mixer or other processor (Tip or Ring is the send with the other being used as the return and again ground is common).
TS
Abbreviation for Tip Sleeve. Tip Sleeve refers to a specific type of phone plug (not phono plug) or 1/4" connector that is set up for two-conductor unbalanced operation. The tip and sleeve are separated by an insulator. The Tip is generally considered the "hot," or where the signal is applied, while the Sleeve is where the ground or shield is connected. Unlike balanced connections the shield connection of a TS cable is required for signal to be able to pass.
TT
(Tiny Telephone) A miniature version of what is known as a phone jack, (phone plug) which is short for telephone jack, from the old days of telecommunications. We commonly refer to this type of jack as a 1/4 inch jack (our modern version actually is slightly different in size), which could come in TS and TRS forms. Switchcraft invented the TT jack (and corresponding connectors) many years ago to serve as a more compact alternative to the phone jack. Later another company, ADC, built essentially the same type of product, but referred to it as a Bantam connector. Nowadays the two names are interchangeable. TT/Bantam jacks and corresponding cables are commonly used in recording studio patch bays.
XLR
Trademarked name for circular 3-pin connectors developed by Cannon (now owned by ITT). "XLR" was originally nothing more than Cannon's part designation for the connector. In fact, you'll also sometimes see these connectors referred to as "Cannon" connectors. XLR has since evolved into a generic industry term, and many manufacturers now make this style connector. In audio work, XLR connectors are normally used for transmitting balanced mic and line level signals.
Pin 1 of an XLR connector is always ground/shield. The connectors are designed so that pin 1 makes its connection first when inserted in a jack; this ensures that the ground connection is made first, helping prevent pops and thumps in the audio chain.
Either pin 2 or pin 3 may be hot (determined by the gear the connector is plugged into), with the remaining pin being cold. To maintain correct polarity in a signal path, it is important to be aware of which pin is hot or cold on all connections, and wire your cables accordingly.
本文转自：China Industry News